The ZeroPlay Guide Bar is a “One-Touch Calibration” miter bar (9 ½” in length) that has two stacked half bars with opposing wedges that expand parallel evenly to fit the exact width of a standard miter slot for a perfect fit and smooth glide, even fits tricky Shopsmith™ or General’s miter slots.
Create perfectly square cross cut jigs WITHOUT any trial and error set-screw adjustment along the miter bar - use our One-Touch Calibration.
Easily square jig to the blade adjustment while securing through the top of the sled - Top Down Installation
Build small cut-off jig easy to carry and store, or build large jig with ZeroPlay Guide Bars in tendon with custom spacing
Replace worn and warped wood runners and aluminum bars that can be a hassle to calibrate
Retro-Fit your existing cross-cut jigs for improved precision
Accurately check alignment of saw blade to the miter slot with a dial-indicator (not included)
Build your own unique jig or jigs with included plan
ZeroPlay Stops serve as an anchor for your clamping devices within the miter slot – shop build clamp plan included
Build table saw coving fence with the ZeroPlay Stop
ZeroPlay Stops limit the travel distance for specialty jig
Because the ZeroPlay Guide Bar is a full profile miter bar that fits the exact width of the miter slot, you have no side-to-side play within the miter slot. The ZeroPlay Guide Bar System is for those who demand absolute accuracy and have zero tolerance for mistakes. Build better jigs in less time!
One-touch Calibration. Zero Side-to-Side Play.
The ZeroPlay Guide Bar is a unique hassle-free miter bar system that is designed to make calibration easier than ever. Its smooth gliding movement makes calibration as simple as one-touch and lock in place. Simply push against the ends of the guide bar within a standard (3/4“ x 3/8”) miter slot or a Shopsmith miter slot and lock the width by securing the three button-head screws with a supplied hex key. The ZeroPlay uses parallel full-profile gliding surfaces, not set screws, to give you the smoothest operating miter bar on the market.
ZeroPlay Jigs. Perfectly Square.
Give your jigs the ZeroPlay effect. The ZeroPlay Guide Bar System is designed for woodworkers who demand absolute accuracy when using their sleds or jigs in a standard miter slot. Not intended for a miter gauge, the ZeroPlay Guide Bar System is designed for user-built jigs. We even provide some of our favorite jig plans with the System. Create a router table jointing fence setup jig or take advantage of an angled off-cut pusher jig. Whatever the use is, the ZeroPlay Guide Bar works seamlessly with shop-built jigs and will ensure that you will be performing with accuracy and precision.
Top-Down Installation. Build with Speed.
The ZeroPlay guide bar uses the top-down installation method, which allows you to secure the bar to your jig from the top. This takes out the hassle of pushing the jig back and forth to align and secure it. Conventional miter bars require you to pull the bar out from one side of the slot, secure it from the bottom, then push it through to the other end of the slot, secure it again, and your lucky if the jig is close to being square. The ZeroPlay Guide Bar System eliminates this inefficient process.
With the ZeroPlay Guide Bar, once the jig is in place and square to the fence, simply hold it in place and secure it where it stands. The result is a perfectly square jig outfitted with an accurate smooth gliding ZeroPlay Guide Bar that will give you outstanding results.
Build Smaller Jigs.
The sleek durable frame of the ZeroPlay Guide Bar allows you to build smaller, more portable jigs for your workshop. Traditional miter bars are large and cumbersome, in turn; the jigs you build for the typical miter bar will be bulky and difficult to handle. This is why Micro Jig designed the ZeroPlay Guide Bar to be about 9 ½ inches in length for maximum stability while allowing the user to build small precise jigs that are easy to handle. Build smaller, more efficient jigs.
ZeroPlay Precision Miter Stops.
Take your accuracy to the next level with the ZeroPlay Stops. These ZeroPlay Stops are designed to travel within your miter slot serving as an anchor for your jig or to limit the travel of your ZeroPlay Guide bar. These ZeroPlay Stops will ensure that you do not slide too far down the miter slot, compromising your project. Simply, slide the ZeroPlay stop to your desired position long the miter slot and tighten the nylon screws. Now, your ZeroPlay stop is ready to help make consistent and precise cuts, again and again. Plus, they are great for user-built hold down clamps along the miter slot.
Getting Started. One ZeroPlay Bar.
One ZeroPlay Bar should be the perfect place to start if you're getting into woodworking and thinking about building some jigs. With our one-touch calibration and top-down installation, you will never know the hassles of aligning set-screws and installing from the front of the table saw and then the back. Lucky you!
For the Jig Master. Two Bars and Two Stops.
Our full ZeroPlay Guide Bar System comes with two bars and two stops. This package is great for serious woodworkers who build multiple jigs and recognize the value of a simple, exact, and trustworthy miter bar. Great for replacing your current runners or building new ZeroPlay Jigs. If you're feeling creative, use two ZeroPlay Guide bars in tandom for building larger, more elaborate, jigs as well.